MTTM_Sisma_3-4_Caldane_calcestruzzo_alleggerito

MTTM. Earthquake

3. Interventions aimed at reducing the excessive deformability of the floors and their consolidation
3.4. Insertion of thin leightweight concrete slabs

MTTM-HEA-3.4

Description

The installation of a thin, reinforced screed made of lightweight concrete is a strengthening technique primarily aimed at increasing the in-plane stiffness and strength of timber floors, thereby improving their ability to transfer horizontal forces between the building’s walls. This method is particularly suitable for floors consisting of timber beams and clay tiles or brick elements, where the limited in-plane strength may compromise their behaviour as a diaphragm during seismic events. The method generally involves laying a thin layer of lightweight concrete, reinforced with a light, distributed reinforcement, over the existing floor deck; this is connected to the timber elements using mechanical connectors and to the masonry using suitable anchoring devices. The lower density of the aggregate allows the increase in permanent loads to be limited compared with a traditional slab made of ordinary concrete. The effectiveness of the measure, however, depends on the continuity of the screed, its correct connection to the timber framework and, above all, its ability to transfer the loads to the perimeter walls. Unlike a composite reinforced concrete floor slab, a thin screed can be designed primarily to stiffen the diaphragm, without necessarily requiring a high degree of flexural interaction with the beams. The design must therefore be tailored to the actual structural requirements, avoiding stiffening beyond what is necessary and assessing its effects on the distribution of seismic forces throughout the entire masonry structure.

Advantages

Lightweight reinforced screed significantly increases the stiffness and strength in the in-plane direction of floor slabs traditionally characterised by modest diaphragm capacity, facilitating the transfer of horizontal forces to load-bearing walls and helping to limit out-of-plane movements in the masonry. Compared with a standard concrete floor slab, the use of lightweight aggregates reduces the increase in permanent mass and thus helps to limit, at least in part, the increase in inertial forces induced by an earthquake. This technique can be particularly useful when it is necessary to retain the original timber framework and floor tiles, but their in-plane performance is insufficient and completely dry-construction methods are not applicable or do not guarantee the required performance. If correctly connected to the masonry, the screed can also act as an effective element of continuity between the various vertical components of the building structure. Experimental applications and case studies show that appropriately connected lightweight topping systems can produce significant increases in the stiffness of the diaphragm and improve the floor-to-wall connection.

Disadvantages and limitations of applicability

This intervention is highly invasive and has limited reversibility, as it requires work to be carried out on the upper surface of the floor slab, the insertion of connectors into the timber elements and the pouring of a wet concrete screed over the existing structure. Where there are floor coverings, sub-floors or floor tiles of particular historical value, the laying of the screed may cause significant interference with the original material and must therefore be carefully assessed from a conservation perspective. Even when lightweight concrete is used, the intervention still results in a permanent increase in mass. This increase must be taken into account when verifying the beams, masonry and foundations, as well as when assessing the building’s overall seismic response. Excessive stiffening of the deck may also alter the distribution of forces between the walls, concentrating the load on the stiffer elements or accentuating any torsional effects in buildings with irregular floor plans. Finally, the presence of damp materials in contact with timber elements requires particular attention to hygrometric conditions and the protection of the timber during the casting and curing phases. In timber-concrete systems, the moisture released by the fresh concrete may cause localised increases in the timber’s water content.

Synergies, interactions and opportunities for complementary interventions

Before the screed is laid, the load-bearing capacity and condition of the timber beams, floor tiles and supports within the masonry must be checked. Any elements that are deteriorated, cracked or have reduced cross-sections must be reinforced or replaced locally beforehand. Particular attention must be paid to the connections between the screed, the timber framework and the perimeter walls. Simply increasing the rigidity of the floor slab is not sufficient if horizontal loads cannot be effectively transferred to the walls. Appropriately distributed and dimensioned connection devices must therefore be provided, whilst ensuring that the masonry in the anchorage areas possesses sufficient mechanical properties. Where masonry is inconsistent or degraded, preventive local consolidation may be necessary. The design must also assess the effects of the increase in mass and stiffness on the building’s overall response and compare the solution with lighter and more reversible alternatives, such as secondary boarding, timber panels, strips or steel bracing, particularly in listed buildings.

Assessment against the criteria

Applicability and impact

Efficacy
Applicability
Environmental sustainability
Reversibility
Impact
Durability

****
***
*****
*
*
****

Cost and construction logistics

Monetary cost
Construction complexity
Availability (time)
Execution time
Maintenance costs
Regionality
Integrative interventions
Use restriction

***
***
****
***
****
****
****
***

Production process

Degree of innovation
Sustainability

***
****

Relationship with the indicators of the Risk Analysis Model

Structural vulnerability: Horizontal structures (slab).

References

Ministero per i Beni e le Attività Culturali (2011). Linee guida per la valutazione e riduzione del rischio sismico del patrimonio culturale con riferimento alle norme tecniche per le costruzioni di cui al decreto ministeriale 14 gennaio 2008. Direttiva P.C.M. 9 febbraio 2011.
Ministero delle Infrastrutture e dei Trasporti (2019). Circolare 21 gennaio 2019, n. 7 C.S.LL.PP. – Istruzioni per l’applicazione dell’Aggiornamento delle Norme tecniche per le costruzioni di cui al D.M. 17 gennaio 2018.
Consiglio Superiore dei Lavori Pubblici (2009). Circolare 2 febbraio 2009, n. 617 – Istruzioni per l’applicazione delle Nuove norme tecniche per le costruzioni, par. C8A.5.3.
Guerrini G., Salvatori C., Senaldi I., Penna A. (2021). Experimental and Numerical Assessment of Seismic Retrofit Solutions for Stone Masonry Buildings. Geosciences, 11(6), 230.